-
March 2023 by Peter Segreto
Unprofessional and atrocious business. Held my motor for my vehicle for months with little to no communication. I had to chase them for answers with no estimated time of repair. No negotiation and refused to even provide parts receipts for big parts going into a motor of my vehicle. No sense of priority or time for me as a customer and would never go back or recommend this type of treatment to anyone.Service: Engine repair
-
March 2023 by LD M
TAKE YOUR BUSINESS ELSEWHERE. THIS GUY TAKES FOREVER TO COMPLETE JOBS, REFUSES TO PROVIDE RECEIPTS AND IS A HORRIBLE BUSINESS MAN. I WOULD NEVER GO BACK OR SEND SOMEONE TO HIS. DON'T WASTE YOUR MONEY.Service: Engine repair
-
March 2023 by EVB
Pleasure working with them. Great machine shop. Competitive pricing.Services: Motor building
-
February 2023 by Peter S.
Unprofessional and atrocious business. Held my motor for my vehicle for months with little to no communication. I had to chase them for answers with no estimated time of repair. No negotiation and refused to even provide parts receipts from suppliers for big parts going into a motor of my vehicle. No sense of priority or time for me as a customer and would never go back or recommend this type of treatment to anyone.
-
November 2021 by carlos merino
Great job on a Hyundai head rebuilding. Only guys I can trust in Westchester and Putnam county
-
October 2021 by Brian Kelly
I have been using Westchester Auto Machine since 1991 they do quality work and have great prices. My shop is almost 2 hours away from Them and it is worth the drive to know the work I need done is done correctly.
-
April 2021 by Underdog 1
Friendly service and very knowledgeable owner. Highly recommend.
-
February 2021 by Michael Zeiber
Terrible, A total Waste of money
-
July 2020 by Thori Bonner
I was in a bind and Will really helped me out. He machined my heads in a matter of a few hours and at a great price (though truthfully I have nothing to compare it to). If I need this type of work done again, I would certainly go back. Thank you, Will!
-
April 2020 by Ryan Collette
Will and his guys are great! They complete the work properly and efficiently with quick turn around time. Will had refreshed an RB20DET head for me and it ran great. I recently dropped off some dirty LM7 junkyard heads that were hot tanked, decked, received new valve seals and were pressure tested. He also installed ls3 valve springs which he had in house! We are lucky to have a great speed shop in Westchester of all places!- Ryan
-
December 2019 by Bart Massi
Over the course of three years of working with Will he has done two engine rebuilds and countless cylinder head rebuilds, all are running great!. Will runs a top notch machine shop! We are sending him another head today for check out and rebuild .
-
November 2019 by One_Clean _s13
Will and his guys are great! They complete the work properly and efficiently with quick turn around time. Will had refreshed an RB20DET head for me and it ran great. I recently dropped off some dirty LM7 junkyard heads that were hot tanked, decked, received new valve seals and were pressure tested. He also installed ls3 valve springs which he had in house! We are lucky to have a great speed shop in Westchester of all places!
-
September 2019 by doug dean
Had him do two motors for my boat. I put them in, and couldn't get them to run right, after many stress filled hours driving myself crazy I finally did a compression test and they both suck they were better before I had them rebuilt.I now have to tear them both down take them out and send them somewhere else to get done. Thanks Will.
-
March 2019 by Charlie B.
The Pontiac 350 H.O. that Westchester Auto Machine rebuilt for me performs better than expected,their attention to detail on all aspects of the entire short block are no doubt the reason.All requests for additional machining were met with a "can do" attitude. I would and have, recommended them to friends needing machine shop services. Their pricing and speed are hard to beat.Thanks Will!
-
January 2019 by Azim Aliriza
Simple block bore and deck. Gave this guy every piece of paper from Nissan FSM for block specifications, taper, bore, out of round etc.. the new pistons with instructions from wiseco. I never had the bore checked by another shop, but the wiseco rings that came with my pistons couldn't even be gaped to the recommended spec because the bore was slightly too big. I had to call and get a recommended larger top and bottom ring gap from wiseco. After a 500 mile break in and 30hours of running time rings stopped sealing, blow by, burning 2 quarts/ hour. Tearing it down and sending to another machine shop to be bored again.
